Using a pressure washer with a water tank requires the correct operation to prevent damage beyond repair. Learn how you can use it efficiently and safely in this article.

Pressure washers are cleaning gadgets that allow you to remove dirt on surfaces, house walls, sidewalks, cars, and driveways. A force is applied to blast water and cleaning solutions in order to remove grime and stubborn stains.

A complete set of pressure washer parts makes cleaning almost anything possible
A complete set of pressure washer parts makes cleaning almost anything possible

Cleaning surfaces become handy and water-conserving when pressure washers are used. In using pressure washers, there must be a water source. A good water tank complements the operation of a pressure washer. However, it needs proper handling to make the pressure washer optimally operational.

For outdoor cleaning where there is no nearby water source, using a pressure washer with a water tank will get the job done
For outdoor cleaning where there is no nearby water source, using a pressure washer with a water tank will get the job done

Regardless of the pressure washer you are using, you must primarily consider the pressure and water flow force. These will significantly impact the functionality of the washer.

Here are the ways of appropriately using a pressure washer with a water tank

Procedure 1: Securing The Pressure Washer To The Water Tan

Step 1: Read

Read the manual that comes with the water tank and the pressure washer for instructions on how to properly set them up. Your water tank should be able to deliver the amount of water per minute specified for the pressure washer.

Step 2: Prepare the water tank

Connect a threader on the bajo fitting of the water tank. Secure an inline to the polyvinyl chloride (PVC) with a Teflon tape. Next to attach are the ball valve and barb connector. Securely tighten with your hands to avoid damages when using pliers.

Step 3: Attach the hose to the tank

Attach the garden hose to the water tank through the barb connector. This must be done securely by clamping the barb connector properly to avoid the leaking of water.

Step 4: Attach the hose to the pressure washer feed line

Make sure there is no debris from the inlet filter of the pressure washer. This prevents any obstructions of water circulation within the system. Make sure to tighten all hose connections to avoid entry of air. Do not use pliers in tightening these connections to avoid damage on the hose and the valve. In order to avoid kickback of the washer, be sure to set the spray wand to a low- or no-pressure mode.

Procedure 2: Turn It ON

Faucets of the water tank must be completely turned on. Expel air from the washer pump system by squeezing the spray wand trigger. Remember that different kinds of cleaning need different types of spray nozzles.

  • General cleaning: flushing nozzle
  • Deep-stain cleaning: blasting nozzle
  • Wide cleaning: detergent spray nozzle
Using the right nozzle for the right kind of cleaning will give the best results
Using the right nozzle for the right kind of cleaning will give the best results

Before cleaning, allow the washer to run for about a minute to warm it up. While using, be mindful on the tank’s water level. Do not allow the pressure washer to run out of water. This can cause serious damage to the washer’s pump.

Procedure 3: Pressure Check

You may adjust the washer’s pressure and spray setting to your liking. If the washer is not producing enough pressure that you need, you have to troubleshoot the washer itself or the valves and hose. Check the following:

a. Enough tightness of the hose connections

b. Setting the spray wand to a low- or no-pressure mode

c. Do not forget to turn the tank’s water faucet

d. Adjust the spray’s pressure setting

Procedure 4: It’s Time To Get the Cleaning Job Done

Now, your washer is ready to use. You can clean almost anything with the use of your pressure washers. Always bear in mind, however, that pressure washers may cause serious injuries resulting from misuse because of the extreme pressure they produce. For your own safety, always remember to:

  • Avoid using pressure washers when working with ladders.
  • Avoid pointing the washer at people or animals. The pressurized water can cause skin cuts.
  • Maintain a distance of at least 6 feet when working around power lines.
  • Use the safety lock on the spray trigger when not washing or when changing nozzle tips.

Finally, before you uncouple the hose, do the following in order: turn the machine off, turn the water faucet off and release all water pressure in the system by squeezing the spray wand trigger.

If you’re looking for the best pressure washer, be sure to check out reviews online like stanley fatmax pressure washer reviews, so you can ensure that you’re making the best purchase.

Working with pressure washers poses a serious injury when not used properly. It is important to gear up and protect yourself at all times
Working with pressure washers poses a serious injury when not used properly. It is important to gear up and protect yourself at all times

Procedure 5: Do Maintenance Procedures

Pressure washers, like any other motor devices, need proper maintenance to keep their optimum performance. They must be stored indoors to avoid damages on the entire washer system.

Conclusion

With the advent of pressure washers, cleaning jobs have never been this easier. Like any other washing devices, using a pressure washer with a water tank requires proper operation in order to achieve its optimum performance. Learning how to run and use a pressure washer with a water tank will surely get you to places. Make sure to follow the indicated procedure of operation and certainly, your cleaning job with a pressure washer will give superb results!